C1318-95(2001) Standard Test Method for Determination of Total Neutralizing Capability and Dissolved Calcium and Magnesium Oxide in Lime for Flue Gas Desulfurization (FGD)
C1319-01(2006) Standard Specification for Concrete Grid Paving Units
C1320-05 Standard Practice for Installation of Mineral Fiber Batt and Blanket Thermal Insulation for Light Frame Construction
C1321-04 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction
C1322-05be1 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
C1323-96(2001)e1 Standard Test Method for Ultimate Strength of Advanced Ceramics with Diametrally Compressed C-Ring Specimens at Ambient Temperature
C1324-05 Standard Test Method for Examination and Analysis of Hardened Masonry Mortar
C1325-08b Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cementitious Backer Units
C1326-08e1 Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics
C1327-08 Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics
C1328-05 Standard Specification for Plastic (Stucco) Cement
C1329-05 Standard Specification for Mortar Cement
C1330-02(2007) Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants
C1331-01(2007) Standard Test Method for Measuring Ultrasonic Velocity in Advanced Ceramics with Broadband Pulse-Echo Cross-Correlation Method
C1332-01(2007) Standard Test Method for Measurement of Ultrasonic Attenuation Coefficients of Advanced Ceramics by Pulse-Echo Contact Technique
C1334-05e1 Standard Specification for Uranium Oxides with a 235U Content of Less Than 5 % for Dissolution Prior to Conversion to Nuclear-Grade Uranium Dioxide
C1335-04 Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation
C1336-96(2008) Standard Practice for Fabricating Non-Oxide Ceramic Reference Specimens Containing Seeded Inclusions
C1337-96(2005) Standard Test Method for Creep and Creep Rupture of Continuous Fiber-Reinforced Ceramic Composites under Tensile Loading at Elevated Temperatures
C1338-08 Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
C1339-02(2008) Standard Test Method for Flowability and Bearing Area of Chemical-Resistant Polymer Machinery Grouts
C1340-04 Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program
C1341-06 Standard Test Method for Flexural Properties of Continuous Fiber-Reinforced Advanced Ceramic Composites
C1343-96(2007) Standard Test Method for Determination of Low Concentrations of Uranium in Oils and Organic Liquids by X-ray Fluorescence
C1344-97(2008) Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Mass Spectrometer Method
C1345-08 Standard Test Method for Analysis of Total and Isotopic Uranium and Total Thorium in Soils by Inductively Coupled Plasma-Mass Spectrometry
C1346-08 Standard Practice for Dissolution of UF6 from P-10 Tubes ,
C1347-08 Standard Practice for Preparation and Dissolution of Uranium Materials for Analysis
C1348-01(2008) Standard Specification for Blended Uranium Oxides with 235U Content of Less Than 5 % for Direct Hydrogen Reduction to Nuclear Grade Uranium Dioxide
C1349-04 Standard Specification for Architectural Flat Glass Clad Polycarbonate
C1350M-96(2008) Standard Test Method for Measurement of Viscosity of Glass Between Softening Point and Annealing Range (Approximately 108 Pa·s to Approximately 10 13 Pa·s) by Beam Bending (Metric)
C1351M-96(2007) Standard Test Method for Measurement of Viscosity of Glass Between 104 Pa·s and 108 Pa·s by Viscous Compression of a Solid Right Cylinder [Metric]
C1352-96(2008) Standard Test Method for Flexural Modulus of Elasticity of Dimension Stone
C1353-08 Standard Test Method Using the Taber Abraser for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic
C1354-96(2004) Standard Test Method for Strength of Individual Stone Anchorages in Dimension Stone
C1355/C1355M-96(2006) Standard Specification for Glass Fiber Reinforced Gypsum Composites
C1356-07 Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure
C1357-05 Standard Test Methods for Evaluating Masonry Bond Strength
C1358-05 Standard Test Method for Monotonic Compressive Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Test Specimens at Ambient Temperatures
C1359-05 Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross-Section Test Specimens at Elevated Temperatures
C1360-01(2007) Standard Practice for Constant-Amplitude, Axial, Tension-Tension Cyclic Fatigue of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures
C1361-01(2007) Standard Practice for Constant-Amplitude, Axial, Tension-Tension Cyclic Fatigue of Advanced Ceramics at Ambient Temperatures
C1362-04 Standard Test Method for Flow of Freshly Mixed Hydraulic Cement Concrete
C1363-05 Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
C1364-07 Standard Specification for Architectural Cast Stone
C1365-06 Standard Test Method for Determination of the Proportion of Phases in Portland Cement and Portland-Cement Clinker Using X-Ray Powder Diffraction Analysis
C1366-04 Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures
C1367-06 Standard Test Method for Dead Load Resistance of a Sealant in Elevated Temperatures
C1368-06 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Ambient Temperature
C1369-07 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
C1370-00(2005) Standard Test Method for Determining the Chemical Resistance of Aggregates for Use in Chemical-Resistant Sulfur Polymer Cement Concrete and Other Chemical-Resistant Polymer Concretes
C1371-04a Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1372-04e2 Standard Specification for Dry-Cast Segmental Retaining Wall Units
C1373-03 Standard Practice for Determination of Thermal Resistance of Attic Insulation Systems Under Simulated Winter Conditions
C1374-03 Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation
C1375-00(2005) Standard Guide for Substrates Used in Testing Building Seals and Sealants
C1376-03 Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass
C1377-97(2003)e1 Standard Test Method for Calibration of Surface/Stress Measuring Devices
C1378-04 Standard Test Method for Determination of Resistance to Staining
C1379-04 Standard Test Method for Analysis of Urine for Uranium-235 and Uranium-238 Isotopes by Inductively Coupled Plasma-Mass Spectrometry
C1380-04 Standard Test Method for Determination of Uranium Content and Isotopic Composition by Isotope Dilution Mass Spectrometry
C1381/C1381M-97(2008)e1 Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts
C1382-05 Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
C1383-04 Standard Test Method for Measuring the P-Wave Speed and the Thickness of Concrete Plates Using the Impact-Echo Method
C1384-06a Standard Specification for Admixtures for Masonry Mortars
C1385/C1385M-98(2004)e1 Standard Practice for Sampling Materials for Shotcrete
C1386-07 Standard Specification for Precast Autoclaved Aerated Concrete (AAC) Wall Construction Units
C1387-08 Standard Guide for the Determination of Technetium-99 in Soil
C1392-00(2005) Standard Guide for Evaluating Failure of Structural Sealant Glazing
C1393-08 Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks
C1394-03(2008) Standard Guide for In-Situ Structural Silicone Glazing Evaluation
C1396/C1396M-06a Standard Specification for Gypsum Board
C1397-05 Standard Practice for Application of Class PB Exterior Insulation and Finish Systems
C1398-07 Standard Test Method for The Laboratory Determination of the Time of Setting of Hydraulic-Cement Mortars Containing Additives for Shotcrete by the Use of Gillmore Needles
C1399-07a Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
C1400-01(2007) Standard Guide for Reduction of Efflorescence Potential in New Masonry Walls
C1401-07 Standard Guide for Structural Sealant Glazing
C1402-04 Standard Guide for High-Resolution Gamma-Ray Spectrometry of Soil Samples
C1403-06 Standard Test Method for Rate of Water Absorption of Masonry Mortars
C1404/C1404M-98(2003) Standard Test Method for Bond Strength of Adhesive Systems Used with Concrete as Measured by Direct Tension
C1405-08 Standard Specification for Glazed Brick (Single Fired, Brick Units)
C1407-98(2005) Standard Practice for Calculating Areas, Volume, and Linear Change of Refractory Shapes
C1408-98(2004) Standard Test Method for Carbon (Total) in Uranium Oxide Powders and Pellets By Direct Combustion-Infrared Detection Method
C1409-08 Standard Guide for Measuring and Estimating Quantities of Insulated Piping and Components
C1410-05a Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation
C1411-08 Standard Practice for The Ion Exchange Separation of Uranium and Plutonium Prior to Isotopic Analysis
C1413-05 Standard Test Method for Isotopic Analysis of Hydrolyzed Uranium Hexafluoride and Uranyl Nitrate Solutions by Thermal Ionization Mass Spectrometry
C1414-01(2007) Standard Practice for The Separation of Americium from Plutonium by Ion Exchange
C1415-01a(2007) Standard Test Method for 238Pu Isotopic Abundance by Alpha Spectrometry
C1416-04 Standard Test Method for Uranium Analysis in Natural and Waste Water by X-Ray Fluorescence
C1417-08 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
C1417M-08 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design [Metric]
C1419-99a(2004) Standard Test Method for Sonic Velocity in Refractory Materials at Room Temperature and Its Use in Obtaining an Approximate Young's Modulus
C1421-01b(2007) Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature
C1422-99(2005)e1 Standard Specification for Chemically Strengthened Flat Glass
C1423-98(2003) Standard Guide for Selecting Jacketing Materials for Thermal Insulation
C1424-04 Standard Test Method for Monotonic Compressive Strength of Advanced Ceramics at Ambient Temperature
C1425-05 Standard Test Method for Interlaminar Shear Strength of 1-D and 2-D Continuous Fiber-Reinforced Advanced Ceramics at Elevated Temperatures
C1426-99(2004) Standard Practices for Verification and Calibration of Polarimeters
C1427-07 Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form
C1428-99(2005) Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Multiple Collector Mass Spectrometer Method
C1429-99(2004) Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Double-Standard Multi-Collector Gas Mass Spectrometer
C1430-07 Standard Test Method for Determination of Uranium, Oxygen to Uranium (O/U), and Oxygen to Metal (O/M) in Sintered Uranium Dioxide and Gadolinia-Uranium Dioxide Pellets by Atmospheric Equilibration
C1431-99(2005) Standard Guide for Corrosion Testing of Aluminum-Based Spent Nuclear Fuel in Support of Repository Disposal
C1432-03(2008) Standard Test Method for Determination of Impurities in Plutonium: Acid Dissolution, Ion Exchange Matrix Separation, and Inductively Coupled Plasma-Atomic Emission Spectroscopic (ICP/AES) Analysis
C1433-08 Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers
C1433M-08a Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)
C1435/C1435M-08 Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer
C1436-08 Standard Specification for Materials for Shotcrete
C1437-07 Standard Test Method for Flow of Hydraulic Cement Mortar
C1438-99(2005)e1 Standard Specification for Latex and Powder Polymer Modifiers for Hydraulic Cement Concrete and Mortar
C1439-08a Standard Test Methods for Evaluating Polymer Modifiers in Mortar and Concrete
C1440-08 Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain, Waste, and Vent (DWV), Sewer, Sanitary and Storm Plumbing Systems
C1441-04 Standard Test Method for the Analysis of Refrigerant 114, Plus Other Carbon-Containing and Fluorine-Containing Compounds in Uranium Hexafluoride via Fourier-Transform Infrared (FTIR) Spectroscopy
C1442-06 Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
C1443-99(2005) Standard Specification for Glasses, Portlight, Circular, Fully Tempered
C1445-07 Standard Test Method for Measuring Consistency of Castable Refractory Using a Flow Table
C1446-07 Standard Test Method for Measuring Consistency of Self-Flowing Castable Refractories
C1447/C1447M-04e1 Standard Specification for Non-Asbestos Fiber-Cement Underdrain Pipe
C1448/C1448M-05 Standard Specification for Non-Asbestos Fiber-Cement Conduit
C1449/C1449M-05a Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe
C1450/C1450M-04 Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe
C1451-05 Standard Practice for Determining Uniformity of Ingredients of Concrete From a Single Source
C1452-00(2006) Standard Specification for Reinforced Autoclaved Aerated Concrete Elements
C1453-00(2006) Standard Test Method for the Determination of Uranium by Ignition and the Oxygen to Uranium (O/U) Atomic Ratio of Nuclear Grade Uranium Dioxide Powders and Pellets
C1454-07 Standard Guide for Pyrophoricity/Combustibility Testing in Support of Pyrophoricity Analyses of Metallic Uranium Spent Nuclear Fuel
C1455-07 Standard Test Method for Nondestructive Assay of Special Nuclear Material Holdup Using Gamma-Ray Spectroscopic Methods
C1456-08 Standard Test Method for the Determination of Uranium or Gadolinium, or Both, in Gadolinium Oxide-Uranium Oxide Pellets or by X-Ray Fluorescence (XRF)
C1457-00(2005) Standard Test Method for the Determination of Total Hydrogen Content of Uranium Oxide Powders and Pellets by Carrier Gas Extraction
C1458-00 Standard Test Method for Nondestructive Assay of Plutonium, Tritium and 241Am by Calorimetric Assay
C1459-04e1 Standard Specification for Performance of Non-Asbestos Fiber-Reinforced Cement Shake, Shingle, and Slate Roofing Systems
C1460-08 Standard Specification for Shielded Transition Couplings for Use With Dissimilar DWV Pipe and Fittings Above Ground
C1461-08 Standard Specification for Mechanical Couplings Using Thermoplastic Elastomeric (TPE) Gaskets for Joining Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems for Above and Below Ground Use
C1462-00(2008) Standard Specification for Uranium Metal Enriched to More than 15 % and Less Than 20 % 235U
C1463-00(2007) Standard Practices for Dissolving Glass Containing Radioactive and Mixed Waste for Chemical and Radiochemical Analysis
C1464-06 Standard Specification for Bent Glass
C1465-08 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment